Need an oil filter, fuel filter or air filter for a Komatsu PC220LC-12? Start with the complete machine model and serial number—not a generic “PC220 filter kit.”
Komatsu’s parts quick-reference guide covers the PC220LC-12, serial numbers 800001 and up. The references below provide a starting point for a quotation. Confirm the current parts listing for the actual machine before approving a replacement.
Engine Oil, Fuel and Air Filter References
The following entries are listed in the quick-reference guide:
| Filter position | Komatsu reference | Quantity listed | Guide interval |
|---|---|---|---|
| Engine oil filter | 6736-51-5142 | 1 | 1,000 hours |
| Fuel pre-filter | 600-319-3610 | 1 | 500 hours |
| Main fuel filter | 600-319-3610 | 1 | 1,000 hours |
| Engine air filter | 2A5-01-35810 | 1 | As needed |
The interval column records what the guide lists. The applicable operation and maintenance manual remains the reference for servicing, including operating-condition requirements.
These are OEM identification numbers. They are not JINGUAN product numbers or confirmation that an aftermarket replacement has been validated for the same service interval.
Why is the same fuel-filter number listed twice?
The guide lists 600-319-3610 for both the pre-filter and main-filter positions, with one unit at each position and different service intervals.
Keep these as separate lines in a purchasing or maintenance list. Combining them into a single “fuel filter” entry can lose the position, quantity or service requirement.
Before ordering, confirm whether the job requires the pre-filter, main filter or both. The repeated reference is not, by itself, an instruction to replace both at every service. For a broader explanation of fuel-filter roles, see the fuel filter and fuel/water separator guide.
What about the air-filter set?
The guide lists 2A5-01-35810 as the engine air filter. Do not assume that this entry includes every element in the air-cleaner assembly.
For a primary-and-safety set, ask for both references to be confirmed. The table above does not identify a separate safety-element number. Related filter types can be reviewed in the air-filter category.
Check the Machine Before Using a Previous Order
“PC220” is not a complete application description. Keep the LC designation, -12 generation and full serial number on the enquiry.
A photograph of the machine identification plate is useful, especially when a fleet contains similar models. Include the engine identification and country of operation when available, then check the fitted filter numbers against the current machine record.
Do not assume that references from a PC220-8, PC220-10 or PC210LC-11 order carry over. Some parts may be shared, but each replacement needs its own application confirmation.
The same applies to PC220LCi-12 and other variants. This reference table follows the stated PC220LC-12 guide scope; it should not be expanded to other models without checking their parts listings.
If a housing or assembly has previously been replaced, provide its identification and connection photographs too. The installed equipment matters as well as the original machine specification.
What Changed in the Maintenance Schedule?
Komatsu’s European launch information states that the engine-oil change interval increased from 500 to 1,000 hours. The parts guide separately lists the engine oil filter at 1,000 hours.
Komatsu’s North American brochure shows the hydraulic oil filter interval increasing from 1,000 to 3,000 hours, compared with the PC210LC-11.
These are changes to specified maintenance tasks—not a single replacement interval for the entire filter kit.
They also do not establish that every aftermarket filter with a matching cross-reference can be used for the extended interval. When evaluating a replacement, provide the intended service schedule and ask what application and performance information supports the proposed product.
The published material does not provide a complete before-and-after comparison of filter media, efficiency or dirt-holding capacity. A claim such as “three times the filter life because it holds three times the dirt” would need separate evidence.
Hydraulic Filter and Breather: Two Different Items
For buyers assembling a wider service order, the same guide lists:
| Component | Komatsu reference | Quantity listed | Guide interval |
|---|---|---|---|
| Hydraulic oil filter | 421-60-81141 | 1 | 3,000 hours |
| Hydraulic tank breather | 208-60-41260 | 1 | 1,000 hours |
The hydraulic oil filter and hydraulic tank breather must remain separate in the quotation. Do not label both simply as a “hydraulic filter,” or apply the 3,000-hour interval to both.
Cabin filters and other service items should also be specified separately when required. This article is a selected filter reference list, not a complete bill of materials for every maintenance visit.
What to Verify on a Proposed Replacement
Once the reference and application are established, check the actual product being quoted.
For the oil filter, confirm the mounting interface, sealing arrangement and relevant performance specification. For the fuel filters, identify the service position and check the supplied connections, seals and any components intended to be retained from the existing assembly.
For the air filter, confirm the sealing surfaces and housing fit. State whether the enquiry is for the main element alone or a matched set.
A product photograph or a similar outside diameter does not settle those questions. Request a dimension sheet and clarify missing information before approving a bulk order. Where a sample is used, distinguish checking physical fit from verifying filtration performance.
Send a Quotation-Ready Parts List
For a PC220LC-12 enquiry, include:
- A machine-plate photograph and full serial number.
- The filter positions required, existing OE references and clear label photographs.
- Quantities for each position, including whether you need individual filters or a service set.
- Any seals, bowls, sensors or other components that must be included or reused.
- The intended service schedule, destination and packaging requirements.
Ask the supplier to identify any proposed substitutions or unresolved fitment questions in the quotation. That makes it easier to compare offers without assuming every kit contains the same parts.
For enquiries to JINGUAN, send this information with your required quantities. Application compatibility, product specifications and supply availability will be confirmed item by item.
Komatsu names and part numbers are used for identification and application reference only. They do not imply original-equipment affiliation.